Okebiz Video Search



Title:Why Use RIGID Insulation board On basement walls
Duration:06:36
Viewed:508,971
Published:31-01-2020
Source:Youtube

Basement Wall Insulation Using Rigid Foam Board

FULL Article: https://www.aconcordcarpenter.com/bas...

Sealing Rim Joists: https://www.aconcordcarpenter.com/sea...

Best practice for basement wall insulation [best insulating and vapor barrier system] is closed-cell foam, the second-best is using foam board, especially if you’re trying to save money. Using a rigid foam board creates a good vapor barrier along with an insulation layer that won’t promote mold growth. Rigid insulation board is also called Extruded Polystyrene (XPS) insulation.

Basement Insulation Vapor Barrier

The simplest way to prevent this water vapor from entering the space is to prevent air movement [moisture] into the basement by installing a vapor barrier. When properly installed, closed-cell foam (spray or rigid foam board) acts as a vapor barrier and insulates. [poly plastic and Kraft faced insulation is not a good solution for basement vapor barriers. ] The main goal for using rigid foam board against masonry walls is to prevent air vapor movement and mold growth, while it can be the only insulation used in a basement insulation system, it’s often supplemented by fiberglass insulation.

The BEST Rigid Board To Use

There are two types of rigid board commonly used.
Extruded Polystyrene (XPS) insulation board
Polyisocyanurate (Polyiso) insulation boar

Extruded Polystyrene (XPS) insulation foam boards deliver long-term stable thermal performance of R-5 per inch. Compared to spray foam, it’s harder to install in awkward areas (for example, in a tight space where a rim joist is close to another parallel joist). Rigid foam is also fussy to install if the rim joists has a lots of wiring and pipe penetrations. But its cheaper and a popular choice if you’re doing a DIY project.

Polyisocyanurate (Polyiso) is a closed-cell, rigid insulation foam board that is bonded to facers on both sides Polyiso is most commonly used due to its fire-retardant properties. Under normal fire conditions, XPS, melts and drips while polyiso, chars over.

The foil facing also helps with the limiting of any moisture travel. Polyiso is commonly used in roof, wall, ceiling and specialty applications within commercial and residential buildings of all types.

Relocate Any Wall Obstructions

Prior to installing polystyrene insulation boards on your masonry wall you need to make sure the wall is clear of pipes, electrical wires and other obstructions. If you do run into obstructions you can start and stop your rigid foam on either side of it and fill that area with spray foam.

Use Insulation Foam Boards [XPS or Polyiso]

Install 2″ insulation foam boards in a vertical orientation, tight to the floor and top of wall or joist bay. See How To Insulate A Rim Joist.

We ensure that the boards fit together using the factory joints, and then return later to tape all seams.

Prior to installing the next insulation board, we add a thick bead of adhesive in the edge groove.

We use DAP DynaGrip construction adhesive for Styrofoam products, and to adhere the boards to masonry walls. DynaGrip is a premium high strength adhesive for heavy interior/exterior construction and remodeling projects.

This multi-material adhesive delivers a powerful instant grab to hold the vertical insulation boards and creates a durable long-lasting adhesion. We apply a zig-zag pattern of 1/2″ bead directly to the wall and press the insulation board in place.

Seal Vertical Joints With Foil Tape

Tape all vertical seams using a foil tape compatible with the foam board. This type of tape has a durable backing, coated with an aggressive acrylic adhesive that offers excellent adhesion, and sealing properties.



Seal Top and Bottom Joints With Foam

Once all of the insulation foam boards are installed to the walls, and the vertical edges have been taped we then seal the top and bottom edge. Using a Pro Series spray gun applicator we completely fill all gaps, remaining penetrations, and any air leaks using DAP Touch ‘n Foam Polyurethane Foam Sealant.

This All-Purpose sealant is a 1-component polyurethane foam sealant that dispenses approved fire-block (ICC-ES ESR-1926) foam.

Seal the Rim Joist and Sill Plate Area

The rim joist is located above grade and for many years we treated it similar to the wall insulation above, by stuffing fiberglass batt insulation in the rim joist bays. This method is no longer recognized as best practice. Best practice for rim joist and sill plate is to seal all cracks against air leakage and then insulate the area.

Frame Basement Walls

Install basement walls up tight to the 2″polystyrene insulation boards. Fiberglass insulation can then be applied to the studs walls, to increase the basement insulating R-value.

SHARE TO YOUR FRIENDS


Download Server 1


DOWNLOAD MP4

Download Server 2


DOWNLOAD MP4

Alternative Download :



SPONSORED
Loading...
RELATED VIDEOS
How to Insulate a Basement | This Old House How to Insulate a Basement | This Old House
08:57 | 613,130
Sealing and Insulating Rim Joists - Best Practice Sealing and Insulating Rim Joists - Best Practice
07:08 | 123,525
DIY Spray Foam Insulation - What You Need to know Before You Start DIY Spray Foam Insulation - What You Need to kn...
08:21 | 229,991
Basement Wall Basement Wall
02:19 | 82,840
Basement Finishing - Part 1 - Insulation & Damp Proofing Basement Finishing - Part 1 - Insulation & Damp...
14:30 | 68,668
Basement Insulation Tips Basement Insulation Tips
02:52 | 241,140
How to Insulate Your Basement: Part 3 How to Insulate Your Basement: Part 3
05:08 | 46,749
Insulation Installation Guide:  FOAMULAR® XPS Insulation for Basement Walls Insulation Installation Guide: FOAMULAR® XPS ...
04:34 | 32,312


coinpayu